Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
Lets say, that I've got a chip with program in its flash. I know I can protect it from being read back, but can I protect it from flashing anything else through debugger interface...
we have two nrf51-dks and we wanna create a ble mesh.
how can we set a ble mesh and same time ble advertising on Nrf51422 DK (PCA10028 V1.2.0) Board with using examples on...
Hello,
is there a possibility on nrf51 8.0.0 softdevice to determine whether particular notification has been received by remote device?
I use sd_ble_gatts_hvx() to send...
I am facing some problems with the app_timer api. In my application I have created two app timers. The timer api is using the swi1 interrupt for its working. I am using it...
During DFU with the nrf Connect app I get the error REMOTE DFU OPERATION FAILED. Here is the log file:
http://pastebin.com/y7hFNSBq
Using NRF5 SDK12 / NRF51 DK
...
Hi
We are very interested to test the wireless range using Bluetooth 5, 125 kbps long range mode.
If we purhase two nRF52840 Preview DK boards, is there a easy way to...
Hi, Nordic
I have two nRF52 and one nRF24LU1.I want to use Gzp. two nRF52 pairs to the nRF24.
I use nRF5 SDK13 GZP device sample, nRF24 Gzp host sample.
But only...
Hello,
Currently i am doing some testing with the NRF52 DK.
I am measuring the time it takes to send and receive a BLE message.
I am using the high bandwidth setting...
Hi all,
Someone can give me a information about the difference between function uint32_t err_code = sd_ble_gap_adv_stop(); and stop the advertising with using the timeout...
hi everyone i'm using 9 axis imu sensor with the nrf51822 board and i'm confusing in how to calculate the roll,pitch and yaw values,can you please suggest me some methods...
I recently purchased the NRF52832-QFAA Nordic SoC, and am having trouble finding information in the documentation about FCC ID and CE mark testing. Thank you.
