Hi! We're evaluating the nRF7002 with its DK. As part of that I'm trying to run the sample in ncs/sdk/v3.0.2/nrf/samples/wifi/raw_tx_packet. I build it with: `west build ...
Hello everybody,
now, I am solving problem with switching off Wi-Fi interface on nrf7002-DK. I am runnig SoftAP example on my nrf7002-DK board. So my board behaves like...
Hi there,
My team and I have recently started work on a project based on the nRF54H20, and for now are trying to get up and running with the samples on the DK.
We started...
Hello everyone! I'm currently working on a custom PCB designed specifically for drone communication . In my design, I'm using the nRF52820 as the main microcontroller and...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
I want to use the MultiActivity Example with the nRF52 with GCC and Eclipse.
In the documentation I ve read that S130 and S132 are supported, but in the directory of the...
When I using the UART port, if I float the port after init the UART it will restart the code, is it need a external pull-up resistor? How about the value?
A quick one, where do I find a list of the err_codes? I have had a look in the documentation and I was expecting to find a table of them, but I couldn't locate one.
Thanks...
Hello!
I am trying to send a notification to a peer device when a certain event occurs. To do so, I'm using the same procedure as with every other characteristic with enabled...
I used the example of the ble_central\ble_app_uart_c and ble_peripheral\ble_app_uart.
It seems no problem for operation when I check only this example.
But I modified this...
Hello Everyone ,
I ahve deveoped the custom board using NRF51SOC and i have flashed the custom board by usign P20 Connector referred below figure now i would like to debug...
If I let the SoftDevice write to my variables directly by having the characteristics point to my app's variables through BLE_GATTS_VLOC_USER - when are these variables actually...
HI,i have some problems about RSSI (51882)
BELOW IS MY CODE. who can tell me why I can not get RSSI from variable t
int main(void)
{
uint8_t *p;
uint8_t t = 0;
...
Hi,
In S130, both central and peripheral modes are enabled. How do you enable just the peripheral mode and not the central mode for S130 so that less RAM space is used...
I am just working through the tutorial on radio notifications and imported "ble_radio_notifications.c" to my application folder and included the header in included directories...
I use NRF51822 Bluetooth 4.0 e-val kit.
souce code is peripheral example.
so, android smart phone and NRF51822 is connection.
result, Pairing success. occur On_ble_evt...
Is it possible to detect a bluetooth (BLE) enabled phone when it enters the room?
I like to use the nrf51822 (BLE-Peripheral or BLE-Central) to detect any phone when it...
Is it possible to have S110 but not more than ~30-40K size? I need to establish communication in order to upgrade firmware over BLE (UART Emulation), but without using such...
Hello,
Situation:
I am trying to write a characteristic to an iOS device acting as a peripheral from a nRF51822 board.
The board has 2 leds (green and red) and a button...
What is the file pstorage_platform.h? Is it an SDK file? Where does it come from? Is it auto-generated somewhere or should it be just copied from an example?
