i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
Hello
Where can I find operating characteristics of pstorage_store and pstorage_update?
Actually, I observe that about 100 ms are needed to update 4 bytes data. For...
Hi All,
I have two application modules which will use the flash , 1) Bond manager 2) configuration file
I have register both modules with different parameter in the initialization...
keil 5.12 could install pack file. I'd like to install S130 0.9 to keil 5.12, but I did not find S130 0.9 pack file. Could I install S130 0.9 manually and could select the...
Hi....
we are having some issues while testing our profiles in ios app.when switch from application to dfu am calling "sd_ble_gatts_service_changed(m_conn_handle,0x01,0x4D...
I'm looking for a simple and inexpensive solution for tying the TX and RX pins to GND after burning the OTP in production. What have other people done? I'd like to avoid having...
We are trying out nRF51822. My colleague has a top of the line Lenovo running Ubuntu and is able to detect the module when scanned. However, my macbook pro Mid 2014 (Which...
Hi everyOne , i have been trying to upload my hex file into my controller, but every time i click the "Load" option in KeiluVision a window pops out..! it shows " No Cortex...
One question came to mind while browsing through the SDK example code documentation:
as there is a blinky and a blinky RTX example, do all the projects which use the soft...
Hi!
I looked through the forum and didn't find the answer.
Our team is developing product with STM32F411 MCU and nrf51422 module. We need to provide firmware OTA update...
