HI ,
I wan to disable the vBus "VBUS is not valid, and the pull-up resistor on D+ is disabled." on nRF54LM20,
I try to write to disconnect usb from PC :
NRF_USBHS...
Hello everyone! We were working with our nRF52DK boards and one of our students had issues flashing a board. He used a recent version of Segger J-Link Commander (V9.30 as...
Hi Nordic Support Team,
We are working on an nRF5340-based application using the nRF Connect SDK and would like to implement FOTA for both the application core and the network...
hello! I'm having problem when trying a repairing after clearing the bond information in the nrf52840 i using pairing via oob , i exchange oob between nrf52840 and RPI using...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Is it necessary to perform the GATT device discovery process whenever two bonded device re-connect? I'm using two nRF54L15-DK boards, one is Central and one peripheral. Developing...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello,
I am a newbie of Bluetooth development. I have a question that what is the difference between ACI (Application Controller Interface) given in nRF 8001 and HCI (Host...
Hello,
I have one Eval-Kit (v2.2.0) and I had no problems with SDK5.2.0 and demo programs defined in nRF51822 Evaluation Kit User Guide v1.2. Now I have installed SDK6...
Hi,
On a nRF51822 (QFAAG0) with S120 softdevice (using the recent PCA 10001 v2.2.0 board), i'm trying to perform these operations successively:
a simple RSSI scan...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I want to use the AES of 51822 and I have read the nRF51_Reference_manual,I cann't find any demo about AES in SDK.Do you have the demo code about 51822 AES encryption...
Help please! I've been using the nrf51822-EK for several months. Everything has been working well.
I updated my SDK in order to be compatible with S110-SD-v6. Everything...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
Hello,
The fact is that I was testing how to OTA update the kit's firmware. I had no problems with the app but when I tried to upload the bootloader.hex includen in the...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Good morning,
Is it planned to raise a new version of this application note but based on the new version of the SoftDevice? If yes, when is it expected?
Best regards...
