nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image
Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
Hello.
When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated.
I would appreciate it if you could tell me how...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
I'm working on optimizing power consumption in my project (using nRF5340DK; as well as Power Profiler Kit 2 which is connected to DK's VDD measurement point as an ampere meter...
Good Day All,
I'm having troubles with my nRF52840. (Specifically the nRF52840 18010 Holyiot module [http://www.holyiot.com/tp/2019042516322180424.pdf]) I've designed a...
I am looking for the nRF9151 variant of this document nan041: nRF9160 production programming . I do not currently see anything available on the technical documentation section...
I am working on CAF example Module and it has 4 pwms in overlay file.
1. Is it possible to add another PWM?
2. Is there any limit to number of PWMs and number of channels...
We have an existing application, based on the nordic softdevice s140nrf52701 that uses the AES algorithm, specifically ECB, CTR and CBC mode. We need to migrate to AES GCM...
Hi.
I’m trying to install Nordic Semiconductor’s nRF Connect SDK (NCS) version 1.9.2 via the command line. The standard nrfutil tool only supports versions 2.0.0 and above...
Hi,
I referred to the zephyr/samples/drivers/soc_flash_nrf/ code, and when I added CONFIG_BOOTLOADER_MCUBOOT=y , the flash storage started from address 0xfc000 . Why did...
Hi,
For a new product we would like to use Midi over BlueTooth (probably BLE). Is there support for this using some Nordic SDK (like the nRF Connect SDK)?
I can find several...
Hello everyone,
I’m facing an issue with my Thingy:91 . It was working fine throughout the day, but after flashing a program onto the nRF9160 , my computer no longer detects...
Hello. I am using nRF52832, SDK ver 15.3 and running it as a peripheral device. I use an interval timer to send a UART to an external device and receive an ACK. After running...
I am using nRF52840-DK with nrf5-SDK version 17.1.0.
I want to use logging system provided but facing issue due to it's complexitiy.
I am not able to find any example...
I'm currently porting the code from our released product built on NRF SDK with nrf52832. For the next version we want to have the option to go to the upcoming nrf54L* processors...
Windows 11 VSCode 1.93.1 nRF Connect for VS Code Extension Pack v2024.9.5
I'm already working with multiple Zephyr development projects (not only Nordic modules) so I already...
