SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
I bougth pca10056 and I need use it with Keil, but I do not find the pack installer for this board on "Pack Installer".
Furthermore, keil does not recognize my board.
...
I am using a lithium polymer 4.2V battery to power an nRF51822 (as a side note the power goes through a voltage regulator before going to Vdd). I want to be able to check...
When calling app_sched_event_put() no check is done whether the exact same record (same data, length and function pointer) already exists in the queue. We have setup where...
Hello,
I've tried to implement a custom service with a custom chacteristic, that shows the values per notification in the MCP (Master Control Panel) in percentage.
I played...
Hi,
I am using NRF24L01 module and I would like to transmit I2S signal through this module. I used SGTL 5000 audio shield for converting audio signal from microphone to...
Hi,
I'd like to determine the cause of a watchdog reset. I was hoping to utilize the WDT event handler (passed in to nrf_drv_wdt_init() ) to record the PC of the application...
I am trying to get the S132 Central Multilink example to run with 20 peripherals instead of 8. So far, I have made the following modifications:
In sdk_config:
Increased...
I wonder about the accuracy specifications in chapter 9 of the ppk user guide. It says +-20% of readout on average value. Is this only the calculated average of the python...
Using S130 to request notifications of radio activity as:
fails with NRF_ERROR_INVALID_PARAM.
Is there a reason this combination is disallowed? The use case for it is...
I would like to add the UART part to my application. But I will get these errors:
..........\components\libraries\uart\app_uart_fifo.c(109): error: #20: identifier "UART0_CONFIG_PSEL_TXD...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
