Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello, I read the instructions here for using the Nordic NRF Connect app for testing the CTS example: https://devzone.nordicsemi.com/f/nordic-q-a/53382/implementing-current...
Hello,
Hardware: nRF52840
SKD: nRF5_SDK_16.0.0
SoftDevice v7.0.1
I am working on creating a multilink central application where my central device connects to 3 peripherals...
Is there an issue with releasing application firmware, say v1.0 with and then in a following release via DFU, say v1.1 with .
I'm trying to understand if a network has been...
The nRF52832 (QFN package), Pin 44 is listed as "No connect" and has an additional description of "Leave unconnected". Question is what negative affect would occur if this...
Hi
I am unable to configure the nrf52840 dongle in client mode in light switch mesh example. I have changed the simple_hal.h to include the dongle board as /** Boards with...
I developed a software based on Blinky. I have been trying to add DFU to the current iOS app which is working properly to be like the Android app.
As I did in Android, the...
Hi, I would like to skip pairing process alltogether and just provide the KEys which were generated for both devices beforehand. My question is only. Is it possible to initate...
I have an application that will have up to 20 devices communicating with a gateway. Each device will need to send around 2MB of data every 5 minutes. We would like to use...
Hello.
I try to BLE and GPIOTE.
The reason for using GPIOTE is to read data from the temperature sensor.
And I want to sending data of temperature sensor by BLE...
Which type of PCB antenna should i use for BLE beacons based on nRF52832, nRF52840 and nRF52805 for longer range applications.?
Can i use the same antenna used in nRF52DK...
Hi All,
There are few chips that Nordic supports Direction Finding.
nRF5340,
nRF52833
nRF52820
nRF52811
Is it possible to know the recommended chip I should...
hi all,
NRF_ERROR_INVALID_STATE is coming when i initialise Ble_stak_init form nrf_sdh_enable_request() function.
I initalised ble once and disabled using sd_softdevice_disable...
Hello,
I am developing on the Garmin LIDAR-Lite v4 , which uses an nRF52840 internally with the programming pins exposed. I am able to run my OpenThread application on this...
Hi
while developing I've discovered that the current tickless implementation using RTC causes the idle task to loop for one tick before waking the next task up.
I've instrumented...
