Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
I am trying to read BMI160 outputs using SPI protocol but I am struggling to get a successful build from my code.
The build fails at the first line of my code...
Hi,
I am trying to write a file in flash(nrf52840) at a particular address & after that i want to instruct DFU module to start FW update from that address?
Is there any...
What are the situations where a SoftDevice calls reset handler?
I have a somewhat heavy data collection (lots of event handling) and those things are logged via RTT backend...
Hello,
I developed an application on a BMD-300-EVAL. This is a evaluation platform with a BMD-300 module (nrf52832 chip + antenna + crystal +...) on it. The application...
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
Hi
The flash data retention time for nRF52832 have been specified for 10 years @ 40°C. Is there any data available what the retention time would be at higher temperatures...
We are developing tracking system for our ground floor car parking but couldn't able to get GPS location.. we install Nordic Thingy:91 inside the steel body. Please let us...
Hello guys,
We are developing nRF52840-based device that needs to act as both BLE Central and Peripheral.
Peripheral role:
In BLE Peripheral mode, nRF52840 should advertise...
I have a need to send pressure data form 1 device to 4 other devices , it is medical application , data rate is in such a way to be in human readable form, can i use nrf24l01...
Hello, Just purchased a nordic NRF5340 PDK from digikey. On plugging the micro USB 2.0 and switching on the device , the device powers up for couple of seconds (LED1 & LED5...
I'm trying to add BLE_UART functionality to a custom board, on top of the already existing USB (and working) USB_CDC CLI. I'm using SDK 15.3.0 and softdevice S340
I used...
