Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am working on a LIN slave.
I have working code on an Atmel 2560, just porting it to the NRF52 now. The complication I am foreseeing is that on the Atmel part I could...
i'm using the sdk only for ble serial data transfer, which i'm not using for this pwm test
all code talks directly to the hw registers
those are some code snippets to...
Hi, There are some older comments. Since situation is changing fast and I am un-sure if these comments are out-dated or not.
ROM size. Some comments said 51 is small...
I'm using nRF connect 2.5 on PC and the latest Android app on a Pixel phone. My firmware is based on SDK 15.1 and soft device 6.1.0. I am using nRF52840-DK boards.
My firmware...
Hi,
I would like to know if the nRF51822 chips come with their own valid IEEE address of if we must buy an OUI and generate our own addresses for use in final products...
Hello,
I propose theses evolutions in nrf_bootloader.c, it allows to use gpregret and gpregret2 for other things:
(nrf_power_gpregret2_get() & BOOTLOADER_DFU_SKIP_CRC...
Hello,
I have questions about Thread protocol:
- Can i ask to network the ID of the last point used to connect a sleeping device ?
- I have a great area to cover so...
I'm trying to develop a beacon application where I dore to read the battery level.
I installed the Segger SES development environment.
If I use the example \examples\ble_peripheral...
I tried to follow the Video on how to use Segger (on this Page. www.nordicsemi.com/.../nRF5-SDK)
for nrF52832, but I get errors when building the Segger Solution: C:\User...
I have an application where I need to be connected as peripheral in 1 connection and as central in up to say 10 connections simultaneously. I posted regarding connection event...
Hi
I've just analyzed a behavior releated to the watchdog and the new SDK 15.1.0 bootloader. The bootloader just reseted after the configured watchdog timeout has elapsed...
Hi,
Currently I'm upgrading our code base to SDK 15. At https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.0.0/migration.html?cp=4_0_1_1_9 there are...
Hello,
I wish to use "ble_nfc_pairing_reference" example with nRF52832 IC and SDK15. I flashed the example into "nRF52 DK" board. When I enable the NFC and BLE on my phone...
Hi,
We have the following problem when start the watchdog from bootloader: the application is started successfully by the bootloader but when enable the softdevice the application...
