Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I've searched around the forum and followed all the advice given in other threads but am still not having any luck.
I've tried running the nRF sniffer on both a...
Hi there. I just got the nRF52840 DK and am trying to get going with it. I have been looking at this getting started page:
https://www.nordicsemi.com/eng/Products/Getting...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
Hello,
I have an nRF52 DK here that behaves strangely since a few days. Hardware id is 0xc7
When I boot it up with my firmware, sd_ble_enable takes around 2 seconds...
Hi
We have used DTM functionality in nRFgo Studio to carry out signal strength testing during the design stage. We now want to automated this testing in end-of-line testing...
Hello,
I beginner for Nordic board, developing small device using BLE.
I build softdevice, bootloader and application. I checked working DFU mode(via serial, not BLE...
What a software i can use for develloping a Bluetooth Profil Mesh (BLE5) ? Hello every body , i want to develop a bluetooth mesh profil and i don't known which a IDE i will...
Hi,
I make my first project with the nRF52832.
On my first pcb the bluetooth works fine, but this pcb was not fully assembled.
Now i have made a second pcb that is fully...
I need to create and update some data record, the record contains some data that will be updated sequentially or randomly. But the sdk does not execute fds_gc automatically...
I am reading through IETF RFC7668, IPv6 over BLUETOOTH(R) Low Energy . In section 3.2.2, it states the following:
At network interface initialization, both 6LN and 6LBR...
