Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
After reading this https://devzone.nordicsemi.com/f/nordic-q-a/3830/what-is-the-value-of-the-gpio-pull-up-and-pull-down-resistor
and seeing that the internal pull-up is...
I'm trying to get readings from an LPS22HB sensor with the nrf52810 using the lps22hb driver in SDK 17.0.2_d674dde.
The lps22hb_init() call completes without any errors...
Hi, I'm using nRF52805 and SEGGER.
The firmware could be programmed to the chip successfully when I use Debug->go. I can connect with the BLE signal.
However, when I use...
Hi! I am struggling with figuring out how to properly set the sampling frequency for the qdec device. I noticed that making changes directly to the members of config struct...
Hi,
I'm setting up SAADC as explained in the examples: First start conversions with buffer 0, then with buffer 1. On the SAADC callback I queue the current buffer for conversions...
I'm developing an app that communicates with iOS apps using Nordic's services.
I got this error during development.
I have three questions about the "peer removed pairing...
Hi,
I want to enable 8 channels of saadc in SE mode with 10 bits of resolution. the number of samples in every packet is 32, which means every channel have 4 samples in...
The problem I meet similar to https://devzone.nordicsemi.com/f/nordic-q-a/60684/nrf5340-pdk---debugger-in-ses-remains-in-bt_enable-forever .
/* Wait til nameservice ep...
I'm interested in collecting the modem core temperature for my applications. After some digging in modem_info.h / modem_info.c , I saw the temperature data structure exists...
I want to use PPK2 to test the power consumption of my user device, I have connected the PPK device to my pc with USB cable and turned on its power switch, but when I opened...
Hi, I am trying to run the sample I2S echo program(nrf-sdk/zephyr/samples/drivers/i2s/echo) on 9160 DK, and am having issues reading any valid data on I2s RX. Codec chip is...
Hello
NRF52840 with own hardware
nRF SDK V17.0.2_d674dde
nRF SDK for Mesh V5.0.0
IDE: SEGGER 5.60
I started with the "ble_peripheral/ble_app_template" example...
I am trying to use the dongle as a BLE sniffer. I have followed the directions on how to program the dongle including downloading and installing the jLink software.
When...
SDK 17.0.2, SD 7.2.0. with secure bootloader, when performing DFU without BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE, nRFConnect will successfully update the app. With BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
