Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I have a simple prototype platform that previously uses nRF51822 which is discontinued. Now I plan to replace the BLE module with nRF52833.
Previously developed firmware...
Hi everyone ,
I want to perform DFU of SD+Bl+APP via UART.
I use nrfutil version 6.1.3.
The Softdevice is s140_nrf52_7.2.0_softdevice.hex and the application is based...
Hello everyone, i'm trying to deal with the ACS714T sensor but i can't find any samples or guide through internet the communication need to be done through ADC and SAADC HAL...
I am using the nrfx_uart and need to disable the receiption. I call nrfx_uart_rx_disable. When done once, the receiption is not working anymore, even when I call nrfx_uart_rx_enable...
I am the digital pcb and fw designer on a project using a dipole antenna defiend by the RF designer ( I have read the posts discouraging that and have taken that into account...
I am studying the ble_beacon example among the examples provided by nordic.
I want to code the beacon's uuid to indicate the mac address.
I studied to find the mac address...
Hi team,
Note that nRF Sniffer already support nRF52840 dongle, but can that sniffer the BLE5 Advertising extension pack?
How to set the sniffer software?
Thanks!...
Hi,
I'm experimenting with the AoA locator receives IQ data on nRF52833 in ncs1.7.1. It worked well when the locator only received IQ data from one beacon. But when multiple...
Hiya. We're building a custom appliance on top of a Nordic chip that talks to an Android/iOS app developed with Flutter and a custom cross-platform Bluetooth plugin.
We...
Hi guys,
I tried to connect to nRF52832 using the app and it was successful. But when I directly use the BLE in the Android system(android 11) settings to connect to the...
Hi. I am new with nRF52 microcontrollers. I was able to create a project (myproject) in the examples folder and compile it with SEGGER embedded studio. I copied the whole...
Hello
I just downloaded nrf sdk 12.3 and am facing a problem straight away where I couldn't find valid answers that would fix my problems when searching this forum and on...
Hi,
The Bluetooth Core specification states that:
Per Bluetooth Core Specification Version 5.2 | Vol 6, Part F, Section 1.
The nRF5 SDK, v17.1.0, DTM Example states...
Hi,
I have a problem on two things
1. I want to advertise my custom 128bit UUID with ble appearance and manufacturer data but when i did my advertising device name become...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I am trying use dfu update my application program.After i program software device/bootloader/app(dfu example...
