Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
HI,
I am trying to port the existing BLE throughput example code to my custom board with nrf52840 with SDK v17.0.2 soft device is S140.
I want my custom board to work...
Hello,
I noticed with the LTE Serial Monitor example code on a custom board with nrf9160 (and also the nrf91dk), the UART interface work initially but sometimes hangs. It...
Hi,
I am working with nRF52833 using the SDK17 Dynamic Pairing example. I was able to expand on it for my use case, and the application is now correctly receiving data...
Hello,
I am using NINA-B406 Custom board which have nRF52833 SOC and using Segger embedded studio with nRF5 SDK v17.0.2 for development.
I want to do the two functions...
Hi, Do you have any documentation at all for the experimental GPS driver? I can't find anything. Google just sends me to a few broken links. Best regards, Jan Erik BikeFi...
Hi, the specification of nRF5 SDK for Mesh v5.0.0. says the interrupt priority has two levels, named priority_lowest and priority_thread.
I am not clear on some things....
After installing nRF Connect for Desktop on macOS, I hit "Install" for Toolchain Manager, and then "Open".
This opens a new window for the Toolchain Manager, which says...
Currently, MQTT is required for nRF Cloud data transmission. We will be using LwM2M as the protocol to send data from our IoT monitoring device to our cloud platform. Does...
Hi, I have a bit strange problems with example project "pwm_library". At first I compiled with segger embedded studio and ran the project on my NRF52-DK board, and it worked...
I have used nRF52811 chip in my custom board.
1. Please provide the First time programming procedure using J-Link (J-Link-Pro tool) interface.
2. We have a nRF52840DK...
Hi teams,
Recently, I upgraded JLink driver to 7.5x and suddenly all of my nRF DK boards are not detected via USB.
All of my 4 DKs shows the same symptom. LED5 near JLink...
I am working on an embedded design that uses the nRF52840 MCU and 2x additional processors (Processor #1, Processor #2).
The intent of the system design requires that Processor...
dear all
I used the lvgl in zephyr. When I made a image rotation, I found that I copied some of the image pictures。Is there anyone in the forum who has encountered similar...
Dear friends: I am based on the following link: devzone.nordicsemi.com/.../device-firmware-update-dfu-with-mcuboot-bootloader Operation steps test the function of mcuboot...
Hello I am using sdk17.0.2 and nrf52840.
I used nrf52832 to combine ble_app_uart and crypto_aes_ctr codes. And now I'm going to move the code to nrf52840.
However, there...
