Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am trying to find a good solution for multiple beacon advertising using s132_nrf52_3.0.0_softdevice and sdk 12.1 on nrf52.
Looking at other similar threads:
...
Hi, there
NRF51822
SDK9.0.0 and S110
How to subcontract in uart nus mode to ensure that each packet does not exceed 20 bytes and is sent as quickly as possible...
Wakeup from system off (not WFE) )will cause a system reset and hence will reset almost all of the peripherals (exceptions are RAM and few registers). RTC will also be rest...
Hello,
Is there a BLE only DFU application like that available on Android? The Android application works fine. The windows version needs a serial port to perform the same...
For synchronizing an external sensor i need to output a 32768Hz clock at a GPIO pin. For this case i want to use LFCLK from the external cyrstal.
My setup:
I use RTC0...
Hello,guys
I have build one application, in which I want to transmit the Image from Mobile BLE to nrf51822 and than after display on display like E-paper.
The use case...
Hi,
I use it as a translator for Google, so it may be strange in context. please understand.
I was in big trouble.
I used the nRF51822, S110, and SDK9 in my previous...
Hi. We are attempting to use the Infineon XMC1202 LED shield with our NRF52 device. The XMC1202 has an I2C address of 0x15E, instead of the traditional 7 bit address. We have...
I've tried linking the ESB library (esb_arm.lib) in Eclipse by adding it to my nRF51822 project's Makefile, but I am still getting undefined reference errors during build...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
Hello,
I'm trying to compile an example of nRF52_SDK_1 but I get this error:
make
Makefile:150: Cannot find include folder: ../../../config/receiver_pca10040
Makefile...
Hello,
I've been reading over different examples and questions on the Nordic Developer Zone but still have some questions about multiple SAADC channels.
1 - If I initialized...
I've been developing an application on the nrf51 DK based on the ble uart application and it's been working fine. I've ported it to a custom board running at 1.8V and attached...
Greetings -
I am using (the slightly out-dated) 12.3 SDK with a nRF52840. I'm also using s132 as my softdevice.
As I've been slowly reducing my RTC interrupt frequency...
