I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
Hello,
I am trying to implement BLE DFU with nRF7002DK and SDK 2.7.0(Sorry but not use sysbuild yet.)
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi! I'm trying to find examples for a use case we might be exploring. Specifically, we'd like to connect an nrf52833/20/other to an Ipad over a USB HID interface. The connection...
I am trying to work through the Dev Academy - nRF Connect SDK Intermediate - Lesson 3 Exercise 1. I have run into a problem in step 8. Everything prior has gone OK and I successfully...
New nRF5340 DK board - PCA10095 2.0.2 2024.32 1050055047
HP Laptop with Window 11
Installed nRF Connect for Desktop v5.1.0
DK board is detected
Attempt to program...
I'm trying to make a template project tidier while waiting for an answer to a question and have removed a load of functions from main to serial.c but VSC is telling me
it...
Hi,
I believe there is a significant inconsistency between the documentation and implementation of AoA antenna switching in the nRF Connect SDK. My testing of this was done...
I have a custom nRF9160 application running based on asset_tracker_v2. It is working perfectly but I am seeing location error messages. The nRF9160 we have does not have GPS...
Hi everyone! I have a custom board with the Adarfuit UF2 Bootloader ( https://github.com/adafruit/Adafruit_nRF52_Bootloader) and a SoftDevice. With the old SDK v2.5.1 I created...
Hi! So I am trying to control two micro servos, MS18 with the nRF connect app. So far I have the code where I can control it with one instance, and hitting the true false...
I am trying to work with a BLE Mesh network. I am using the nRF5340 as a light and another board, the BGM220, as a switch. Both are provisioned and configured, but the switch...
Hi everyone,
I'm currently trying to build a program with the extension "nRF Connect", and here is how i proceed :
- add build configuration --> nrf5340_audio_dk/nrf5340...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
