Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello,
Can the NRF52840 module connect with normal Bluetooth modules (such as HC05, HC06)? Is it necessary for the normal Bluetooth module to have BLE support? If so, can...
Dear Devzone,
I can no longer build Nordic's Wifi provisioning (BLE) sample together with custom nanopb code using SDK version 2.7.0. It worked fine in 2.6.1.
Steps to...
I have followed the installation instructions for the nRF52840 on 2 separate Macs using the latest version of all of the packages AND using the proper packages for the respective...
Hi,
If I launch "nRF Connect" inside of VS Code, it uses PowerShell by default.
But if I use the Toolchain Manager, it will open the Command Prompt terminal instead...
Hi all,
We have an application which uses both MCUboot and a watchdog timer. This combination seems to be causing issues anytime we attempt a soft reset using sys_reboot...
Hello Team,
I have have loaded the modem FW 2.0.1 and Serial LTE Modem application on my NRF9151-DK from Quick Start. I wanted to test the RAI release functionality and...
Hi,
If the image we falshed using mcumgr is 90% of the allowed image size mcumgr flashes the unit without a problem, If the image is 98% the proccess seems stuck.
...
I am receiving bytes from a GPS module and passing them to BLE UART example app configured to use UARTE1 and asynchronous API.
After few minutes of running it starts leaking...
Hello everyone, I have two nrf5340 kits. I run "Bluetooth Direction Connectionless" applications with these kits. I also have a CoreHW brand AoA antenna. My question to you...
Hi, I have a custom board running with the nrf9160. It also has the npm1300. I have it set up so that it is configuring the pmic and then turns off the cell and goes to sleep...
Hi
Can we use nrd52840dk as bluetooth(for data transmission to user created mobile app) and to calculate distance using multi carrier phase difference method between itself...
We are having an issue with
This happens to us because we are using the NRF carrier library, and in the carrier library, when you are trying to power off the modem,...
Hi, I'm coding a nrf55832, my code uses TWI, UART, SPI, app_timer, nrf_drv_timer. The code was going welle until i add the saadc. When i call the nrf_drv_saadc_init function...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
