the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
v2.8.0,nrf54l15,hello world demo (Add CONFIG_SERIAL =n to pri. conf),The normal compilation is 3uA, then add sysbuild.conf and write SB_CONFIG_BOOTLOADER_MCUBOOT =y
, and...
Hello,
We are currently looking to implement an RFID tag reader in a project I am working on and I am wondering if the NFCT module can be used to read an RFID tag such as...
Hi
Hope someone can help me with the following:
I am using SDK 17.1.0 and SES (Release 5.68). I have copied the entire SDK and all project files to a cloud-based disk...
My Nordic device (nRF52833, using SDK 2.1.2) is a peripheral. I need to periodically transfer to it large amount of data from central device over connectable Nordic UART Service...
Hello,
I am working on Find my implementation . In my project , I don't have prj.conf but prj_ZDebug.cnfg and prj_ZRelease.cnfg are there.
I want to update few configuration...
Hi,
I'm trying to create a custom board definition for our project. So far, I used the nRF5340DK's board definition, removing unwanted definitions and aliases from the DK...
I am receiving the error "qspi_nor JEDEC id [ff ff ff] expect [c2 28 17]" on device bootup. I am using the nRF52840. I have the qspi disabled in my device overlay.
This...
I just move code from main.c to other files for it is too chaos to lay them together in main.c.
I got this error forever after trying what I can image,except delete "static...
Prior to moving to sysbuild, we were dynamically settings a CONFIG_ variable in our `CMakeLists.txt` based on the board passed to west. And this was working fine.
if...
I've had trouble getting the MCUboot to compile for our application which runs on the nRF7002DK board, and I have similar trouble with the Lesson 8 examples on the nRF7002DK...
I have searched this website,there is only 1 post,but that is not my scenario.
I think this is a normal use case:
There is a struct:
I want to allocate a queue for...
Hi!
I have a bootloader using SPI 3 for a bootloader LCD animation. Unless I attach an RTT console, the animation causes my DFU to fail 100% of the time. It is making me...
Hi,
Since I want to flash the factory data later, I don't want to use the default certificate. I set CONFIG_CHIP_FACTORY_DATA_BUILD to n in prj_release.conf , but a compilation...
Hi Sir, We are planning for a Hardware deign by using nRF52833 and we are stuck on what should be suitable the supply voltage. In some case the data sheet showing that it...
