Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi everybody，
Now I want to integrate nrf52835 into the android system. Using ble is like using anroid's bluetooth.I finally want to implement pairing, communication, opening...
Hi,
I have modified the HRS example (central+peripheral) from SDK 17 to operate in Long-Range mode (PHY CODED). This appears to work correctly assuming that a bond was...
I have succeed transferred data from PC to NRF52840 dongle and managed to receive it back on the PC.
But i want to be available to manipulate the data in NRF52840 dongle...
Hi Team.
I need to know the time elapsed for a set of instructions executed and for this to implement I tried the API app_timer_cnt_get (); in app_timer.h, but it returned...
Hello, I am not able to send sms, and probably connect to LTE-m. I am using at_client example, modem version mfw_nrf9160_1.3.0, nRF connect SDK v1.5.1, v1.6 tried on both...
I have a question:
I found a problem when using D:\nRF52832\examples\ble_peripheral\ble_app_uart sample code and SoftDevice S132 on PCA10040. (nRF5_SDK_17.0.2_d674dde) ...
Hi, Can someone please guide me on the best approach to getting started with Bluetooth mesh application with Nordic thingy 91 (nrf52840). I have try to build the sample code...
Hello,
I found this picture on Nordic's official website
1、Can only proxy node connect to mobile phone and GATT?
2、
I open mesh example (dimming), which contains...
Heelo, i'm trying to use a nordic nrf5340 as a provisioner for the remaining network however i'm getting an error on sending the app-key to the un-provisioned node (I'm using...
Hi, I'm sending SAADC data via BLE. If my SAADC_SAMPLE_RATE is high(e.g. 250ms), the code works perfectly fine. However, if I sample at a fast rate (e.g. 10ms), there will...
Hello,
I posted the following ticket, which has been replied to but it is marked as "Content under review" :
https://devzone.nordicsemi.com/f/nordic-q-a/78575/upgraded...
Why is it so easy to disconnect when upgrading to a few points? The upgrade may be complete
I used SDK 17.0.2's ble_APP_ButtonLess_dFU routine
Do you know? Thank you...
I am trying to build example project in Segger studio but getting error as below............................
Building ‘light_ctl_client_nrf52832_xxAA_s132_7.2.0’ from solution...
Hello everyone,
I am totally new on bluetooth configuration. I have LIS3DH accelerometer from adafruit. and i have nrf51822 bluetooth beacon kit with me. I want to connect...
