Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hi,
I need to connect nrf52833 (BM833 module) with host controller. what are all the interfaces needed to communicate with host controller? help me out in this.
Kindly...
I used 2 channel saadc, channel 1 and channel 3.
Maybe in the first few minutes, it's done ok,
p_event->data.done.p_buffer[0] is belong channel1 adc value
p_event->data...
Hello,
We have integrated the FATFS example as shown in the usbd_msc example project into our own firmware application. It works perfectly on the nRF52840dk and when we...
Hi,
I want to check time line of my project using segger SystemView.
- SDK 16.0.0v
- ESB example
- nRF52832
When Start recording, "Could not find RTT Control Block...
Hello Team,
I want know how to use RESET pin [pin. no. 21] as a GPIO.
I followed below thread but it not work for me!
devzone.nordicsemi.com/.../disabling-pin-21-of...
Hi:
What's the marking on the nRF24-LU1+?
Marking exactly "nRF24-LU1+" or any chance marked as "nRF24-LU1" instead? Your big assistance & prompt feedback is much appreciated...
I am using NRF52810 in : In advertising mode not able to erase or write to flash sd_flash_page_erase. hungs up via processing commands from nrfx_twis_state_machine
Hi,
I'm developing a custom application starting from ble_hrm_freertos application. When NRF_LOG is enabled there is no way let the chip in low power consumption. I found...
Dear Technical Support,
I have faced a problem debugging firmware on our custom board based on Nrf52811. We use j-link EDU and Segger Embedded Studio as development tools...
Hello Nordicsemi community,
1) manual build of mcuboot - When trying to build the mcuboot for nrf5340 via the mcuboot/samples/zephyr via the west build command, the build...
HI , nrf52832 with SDK v16 on that using this nus example location below mentioned
examples\ble_peripheral\ble_app_uart\pca10040\s132
in this example, didn't change...
Hello,
I have recently received the nrf5340 development kit as part of the Hackster contest.
I followed the webinar and to get started
1. Connected board via micro USB...
I started a new ticket since I got a solution to not connecting to the cellular network. Apparently the iBasis sim is not working so I acquired a Hologram sim. I now can connect...
the code yesterday when debug can pop out voltage ,i do not chang anything today ,the code can not run the location ,i make three breakpoints in code and debug ,the code only...
First day using the new dev kit nRF52833-DK. Connected it up following the instructions on nordicsemi.com/start52833dk - computer won't mount the JLINK removable disk so I...
