Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I receive my nRf-9160-DK but decided to try to get the nRF52840-Dongle working first, Simply walk through installing nRFUtil, following the directions I ended up here: https...
Hi
When programming /NordicSDK/v1.3.1/zephyr/samples/basic/blinky in the cpu_app_ns version, it will not start. It is starting when I compile it as a secure application...
In our application we have an RC network (1kOhm-100nF) on pin AIN1. We charge the capacitor with a defined pulse length and then measure the voltage.
At the desired voltage...
Hello,
I can connect to the Segger JLink plus device using USB but when I try to connect to a Segger JLink pro via Ethernet, nrfjprog I receive the following message " There...
Dear Nordic support,
I'd assume it should be OK to allow nrf52840 to advertise in dual phy mode - primary in 1Mbps and secondary coded phy so that phones with and without...
I followed the "Getting Started Assistant" and can import and build the nRF9160 side.
SES -> Open nRF Connect SDK Project:
Works, "Build Solution" works, all seems...
nrfutil version 2.3.0 correctly fails with message " Application file not found." but incorrectly sets the return code to 0
nrfutil settings generate --family NRF52 --application...
I know it basic question but i need direct answer with numbers(exact voltage accuracy)
and i am very much confused to understand about adc output calculation please help...
Hello,
I'm attempting to enter System OFF mode via sleep_mode_enter() using a long press. However, I want to wake up from System OFF using that same button. The problem...
Hi to everyone,
I am having trouble establishing a network connection with NRF9160 Dk. I use a local SIM and according to the information I got from the provider, there...
Hi Nordic
I am using mesh sdk4.1 LPN example to develop a LPN product, we seems found that LPN's RF range will degrade large compared to common mesh node.
We want to try...
hello Nordic
i am working with nrf52840, sdk16, over the peripheral app_ble_blinky example
my system will go to sleep mode for 10 minutes each time, i wonder if there...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
