Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi Sir,
I use the example ble_app_uart_c, the program runs to APP_UART_FIFO_INIT() in uart_init(), an error will occur, and the program jumps to NRF_BREAKPOINT_COND -->...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
Hi, Im new here and microcontroller programming... I curently waiting nrf52840 PDK so Im only quick read SDK and documentation... Before Im program only devices with .NET...
Hi, I cannot open my project using SDK v1.3.0 (nrf9160dk_nrf9160ns selected board) I installed the v1.3.0 using nRF Connect v3.4.1 - Toolchain Manager I already downloaded...
Dear Nordic: I have issue about connect handle. My product supports 1 peripheral and 3 central roles. 1. For this configration, i am not sure handle 0 is resverd for peripheral...
Dear all, I have a question about IV index and sequence number in mesh network. If i have 3 nodes success provisioned. I will only power on 2 active node ( node 1 and node...
Can't see why this is occurring. I've checked my custom board and the reflow of the chip under microscope. The doc indicates this pin isn't linked to a peripheral. Despite...
I am using Nordic board to drive an accelarator. There is already an exist project and it can run successfully. I want to combine this project to a new project and it has...
Can I use the nrf52810 internal temperature sensor to measure ambient temperature? I know it is designed for die temperature but I don't need to know the accurate temperature...
Hello,
From my understanding, I should integrate the LwM2M Carrier Library connection as the first step in the boot process and once I have received the LWM2M_CARRIER_EVENT_READY...
Hi Team,
If we send 20 bytes of data to AES-ECB 128 bit (CC310/ mbed TLS) Crypto engines for Encryption/Decryption due to bytes padding, how many bytes it will become...
With iOS and Android smartphones we are advertising some ble frames.
With our own code on the nrf 52840 we get around 2-4 advertisements each seconds on the nrf 52840 chip...
Hello,
I am trying to use the peer manager on a nRF52832 acting as a peripheral with both bonding and legacy pairing on SDK 16.0.0.
The application configured with bonding...
I am using version 4.1 of the Mesh SDK and version 16.0.0 of the nRF5 SDK on Windows. I was able to successfully generate the ninja build files using CMake. However, when...
