I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi All,
I am using Segger ISP1430603E board to program my nRF development kit. ( ISP1507AX )
With SES I am able program, debug the application.
I would like to program...
Hi there,
I am wanting to develop a custom PCB for the nRF52833 SoC. I am basing it off the nRF52833 DK! As such, most of the schematic labels are identical.
For our custom...
Hi,
When I do a secure DFU (screen dumps pasted ), it failed with error code 0x8005. It worked on WIndows 7 PC.
//==================Linux System Report
# nRFConnect...
where is UARTE configuration in sdk_config.h? According to this doc (for SDK15.3/UART):
infocenter.nordicsemi.com/index.jsp It seems I can follow the steps to enable UARTE...
Hi,
I am using 2 PCA10040 kits provisioned in the same group. I want to change the payload on button press event from client side which I can receive on server side. How...
I have a nordic kit but the dongle or the kit is not recognized by the computer. Is there a driver that needs to be installed before this will happen? I've already installed...
Hello Guys,,
I am trying to migrate my project form keil to segger embedded studio. My product is based on sdk 12.2.0, using softdevice s130 on nrf51822. I searched for...
Hi,
we have two nrf52840 which shall connect very quickly.
The scan+advertise cycle is very fast (we have no bootloader). After switching on the peripheral it is recognized...
Hi,
I run into issues working with ads1220. Its behaviour is really strange. When I test it, data output with continuous measurement is 0. In few cases, when I swap din...
I have an nRF52840 dongle that I am using to connect and read/write to a client unit. I have been able to use the nRF Connect Bluetooth Low Energy program to control the dongle...
Hi,
My product continues adv mode after connected with mobile until the amount of connection is full. By the way, there are 4 connect handle in my product.
My client use...
the nrf51822 is working as a peripheral advertising the data like
0x0201061416FFCB113C01271119359426040A6E189C000000050852545F54,
which contains three data typs:
020106...
1. Why is `libusb-1.0.dll` bundled for MacOS and Windows? Note: I'm not question this, just want to learn why. Are they not installed by pip if listed as a requirement?
...
