I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
I am looking at the ble_app_buttonless_dfu/main.c
This implementation is initializing the queued write module. Is this required now for DFU operation? We currently...
Hello,
For some reason whenever I try to pip install pc-ble-driver it will only ever install version 0.11.4. This causes a problem since I need the nrfutil library and the...
I sent some nRF9160 prototypes down to a CTIA certified test lab in North Carolina to do carrier TRP and TIS testing. When they add their test sims they seem to be unable...
Dear Sir,
I am new in embedded.
I start work on nrf9160.
I have to acquisition periodically through mqtt protocol, a data, with total space of approximately 30 kb, and...
I have installed SEGGER Embedded Studio for ncs sdk. I have installed everything else required to use NCS sdk.
From the command line at ncs/zephyr, I can successfully run...
Does Nordic recommend a specific version of SES? Should I just download the latest version direct from Segger or do I need a special version of SES to have full compatibility...
Hi Guys,
I was able to connect a second uart to the evaluation board and receive over uart.
however I didnt find an example of how transmit a buffer over uart.
is there...
Hi, we have a product that we want to update with new fuctionality, We use latest S110 for NRF51822 and would like to have more than 2 ppi groups useable.
In what scenarios...
Hello folks I have been struggling for some time with the driver for the MCP23S17 in Zephyr. I have already tried this code: https://devzone.nordicsemi.com/f/nordic-q-a/64024...
Hello I am developing a device that uses BLE.
User will connect bluetooth directly the first time they launch a custom app, and they will try to connect automatically the...
Hello I am using an acconeer XM122 / XB122 radar sensor with the integrated psco nrf52840, it turns out that I have mistakenly deleted the bootloader so I cannot flash with...
Dear,
I am using nRF9160 DK,
I can re-define pin for UART0 and UART1, from UART0, i can receive data from UART0/UART1.
Now, I want to send data to UART1.
Plz...
Hello,
I am using nRF51822, SDK12.3.0, pca10028, S130 as a central scanner.
Now I set the scan interval to 100ms and the scan window to 50ms. It is planned to use 50ms...
Hi,
I want to know what is the additional current or power consumption when the temp sensor is acquiring data and operating as intended.
kind regards,
Erick
Greetings,
we have a custom pcb with nrf9160 and are using nrf-sdk v1.3.0 and mfw v1.2.0
Sometimes when connecting to lte the code crashes:
The code in question is...
