Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi guys,
I'm currently using SDK 15.0.0 in Keil MDK and making use of the new NRFX drivers.
Similar to the issue detailed here: https://devzone.nordicsemi.com/f/nordic...
Hi,
In the documentation , you have specified that the nRF Toolbox is supported for mcumgr FOTA.
However, from our tests, it seems that it is not true. Could you please...
Hi,
I'm experimenting with the lwm2m sample on the nRF9160-DK and I enabled the firmware update pull support through a COAP to HTTP proxy :
then simply added :
and the...
Hello peer developers,
This is a general question and dilemma I am dealing with and I wanted to get your opinion.
I am working on a project to implement a short range...
Hi,
Here, i have using two I2C functions EEPROM + SENSOR with nRF52832.
Initially, using ble_app_uart example to read Sensor data using TWIM.
Every minute read Sensor...
I started with ncs/nrf/samples/nrf9160/lte_ble_gateway and have taken parts of ncs/zephyr/samples/subsys/fs/fat_fs to get SD card support
prj.conf
CONFIG_NEWLIB_LIBC...
Here are some of the issues which I am facing in SEGGER Embedded Studio since I updated to nRF Connect SDK v1.3.0:
After I press Debug, Go, a dialogue box opens asking...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
The serial_lte_modem sample is heavily broken. Unlike the AT client sample which simply works with PuTTY out of the box, for the serial_lte_modem you need to configure PuTTY...
Hi all:
I am using sdk 16.0.When put system on idle mode call two times sd_app_evt_wait it works well.But I want to save power,so before enter idle mode,but when I call...
Hi despite trying 3 different approaches (even using the Nordic driver lis2dh12 on a blinky-based project and installing Segger Studio to step/debug into the library code...
I wish to send a message from the nRF Cloud terminal to my device that will land in this branch of nrf/applications/asset_tracker/src/main.c.
} else if ((cmd->channel =...
We have a custom radio protocol that manipulates the radio registers directly (on the '32) and I'm evaluating whether or not we can switch to the '33 to use it's angle of...
i have used a example of ble_app_template in ble_peripheral of SDK15.0,when code run in ble_advertising_start,return errcode 8.
i have checked low speed Crystals，it's ok...
I get error 0x3401 in ble_app_uart_pca10040_s132 (nrf52 dk, sdk17) in ble_nus.c line 95:
err_code = sd_ble_gatts_value_get(p_ble_evt->evt.gap_evt.conn_handle, p_nus->tx_handles...
