Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Summary
With CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and CONFIG_OPENTHREAD_TREL=n , the Zephyr/NCS build fails to link:
ld.bfd: ... openthread_platform.a(trel.c.obj)...
Hello,
I am currently working on a new design based on nRF9151. This design is the evolution of a previous PCB.
The device uses a combined GPS and Cellular antenna, which...
Subject: Support Request for nRF7002 Integration with ThreadX on STM32
Hello Nordic Team,
We are currently using the nRF7002 with our STM32-based device. We have completed...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
Hey there!
I am currently in the process of trying to setup a simple ISR routine triggered via GPIOTE.
However, when calling nrfx_gpiote_init() or nrfx_gpiote_input_configure...
Hi together!
In my current project I would like to send some sensor data to an Azure IoT Hub, by using a nRF52840.
In the first step and for evaluation I used a nRF9151...
Problem: We have a huge variability in received RSSI (see picture) despite both devices being stationary in test setup. For our use case, accurate RSSI is critical. nRF52840...
Hello DevZone
I am currently facing an issues with device already installed at my customer. Devices are based on nRF9160, firmware based on SDK 2.8.0 and modem 1.3.6. Once...
Hi, Background For some time now I have been troubled by a bug in one of our products acting as a BLE central device. The bug manifests itself as the central reporting that...
I see that the nRF5340 is certified PSA level 2 whereas the newer nRF54L15 is certified level 1.
You claim the nRF54L15 is " designed to meet PSA Certified Level 3 ". I...
Hello Nordic support
I have encountered what I think is a bug in ICMSG. The attached sample shows the following behavior:
The first time it runs, the app and flpr CPUs...
Hello Team,
I am not able to flash any firmware to nRF5340 which is available in Thing 91x. I had tried peripheral_lbs example which was working fine. When I tried to...
