Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
Hi , a day ago i recived my first dev board from nordic semiconductors, the nRF5340 . Until now I only coded for AtMega328 , esp32, esp8266 and other microcontrollers like...
I am trying to build the aws_fota example project for the nRF9160 using the nRF Connect SDK and the Segger IDE. We currently have v1.5.0 downloaded. The project is not compiling...
Hello everybody,
i use two nrd52 dk boards with nrf mesh light server flashed on them (mesh sdk 4.2.0)
They are configured over nrf mesh app to be in the same network...
Hi, I have nRF52840 DK. How can set the max range? or how can increase/decrease the tx range? Also is there any range extender to improve range? Thanks!
Hi,
I am currently doing a uart dfu over 2 nrf 52840 dks on a Windows PC. I have been using the example found in ...\examples\dfu\secure_bootloader\pca10056_uart_debug supplied...
