I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi All,
Is it possible for me to broadcast multiple&different type of beacons/advertisement, for example ibeacon, eddystone, unconnectable-advertisement, connectable-advertisement...
Hello, I would like to use the pc_ble_driver_py with sd api v6. I can see in the CMakeLists.txt where I can change set(SD_API_VERS "2;5") to set(SD_API_VERS "2;6"), and it...
Application Info:
I am working on developing a synchronized mesh network of low power sensors. I am trying to maintain an average power consumption of 100's of µW while...
Hello, there,
I am trying to get the UARTE working on a custom nRF52840 board. In my setup, I am expecting a response to every transmission on UART.
Here's my setup...
Hello,
Would appreciate current-day thinking regarding unused GPIO pins. Our product uses Laird's BL652, which embeds the nRF52832. Many GPIO pins are unused. I've looked...
I am new to nRF9160 development board. I have just opened the board and tried to connect following the startup instructions. I was able to see LED 3 and LED 4 blink the first...
Hi,
I am trying to get a bootloader to work on the nRF52832 and struggling to get the application to run after a DFU. I could not get this to work on my custom board and...
First of all, thank you and kudos to Nordic Support Team for having an awesome and functional forum.
Having said that, I have a question related to the architecture of mesh...
Hello,
I am trying to analyse my project my source code with sourcetrail (give graphics with calling functions).
During indexing task, some libraries are not found like...
Hello,
When I run the ble_app_template application from the examples, sd_app_evt_wait() cause an error and the app to crash. So I've put my project in debug mode (DEBUG...
After successfully running the GPS and acquiring position the application goes into an infinite wait loop when attempting to start it again, but only if either or both of...
Hi all,
I upgraded my Sony Xperia XZ2 Compact to Android 10 recently and am no longer able to find BLE5 devices using advertising extensions in nRF Connect (or any other...
Hi,
I know that many people ask this question on different posts but I was not able to find the right solution for my case.
I am observi ng an average current of 4.7uA...
Hi Nordic-Team, I would like to setup a testbed that should be used to measue/evaluete the power consumption of a nRF52840-DK with a connected secure element (like OPTIGA...
i am using winc1500 for wifi connections , i tried through uart too but it doesn't work . Now i want to execute thrugh spi any example or githib code is available
