Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi,
A new modem firmware for nRF9160 has been released. Is it safe to update the modem firmware of Thingy: 91 to v1.1.1? We can download the firmware from nRF9160 SiP page...
Hi,
I'm trying to merge Serial and BLE DFU. I have followed this .
I have used BLE DFU example as base code and added Serial DFU dependencies.
I'm able to do BLE DFU...
HI,
i have made 3 customer board
they all use the same spi flash mx25v8006e
and the first two board have the spi pin : sck 3, miso 1,mosi 0,ss 2
but i change the design...
All I want to do is use the "Advertiser" tab in my nRF Connect android app and force it to broadcast using a custom 128-bit UUID.
I am struggling to figure out how to do...
I have tried combining a working SDK16_98a08e2 MPU6050 example with the SDCard example in the same SDK, however it seems they are incompatible because the MPU example uses...
Hi,
I am developing a device with nrf52840 soc, I need to know that there is any unique and unforgettable id in this chip that with that I could differentiate between...
Hi, Just wanted to pass this along... with the latest Raspbian (09/26/19) the thingy52 will consistently disconnect after about 90 seconds (+/- a few seconds). You can easily...
Hello,
I have two boards of nRF52840, one being central and the other is peripheral. On the central I've put the code from ble_app_multilink_central and on the peripheral...
Hello,
I see this type of query or GATT error has been asking continuously. I have gone through all the same Q&A but not able to solve my query. I have tried all the possible...
Hello Nordic support,
I was referring to the RTC example in nrf52 SDK where an interrupt is triggered on Compare Counter event. In the example, the interrupt is triggered...
I am trying to make custom BLE service to send the data from one nRF52832 to another nRF52832 but we followed the below tutorial "Bluetooth low energy Advertising, a beginner...
Hello,
We are developing a device that needs to get local binding info on init to see if it needs to send data or not to an on/off server in a remote device.
Is there...
Hi,
I'm using nRF52832 board and I'm integrating the Bluetooth beacon sending in the Bluetooth Mesh example. I've edited the Mesh Beacon example in Mesh SDK v4.0.0 with...
I am working with ble_app_uart example. I have added a new folder by name custom_folder in $(SDK_root)/, the same places where folders like library, softdevice, ble, boards...
