Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hi, I'm working with nRF52840DK. I need to run in Direct Test Mode, and to see RSSI & PER. I tried nRF Connect - Direct Test Mode, but it shows only the number of received...
Hi engineers,
I want to transplant demo "usbd_audio" from pca10056 to pca10100, what should I do?
I found a relevant ticket said that
Change board config.
Change...
Hello DevZone,
For a project I'm using the TAG-4 NFC writeable NDEF message example in my SDK and I had a question if this message is always stored in flash or if it is...
I have two nRF5340PDK, both of which would have worked normally. Then I accidentally download the firmware of 52840 version into nRF5340PDK by GProgrammer, which made them...
Hi,
How can I know whether the BLE link between my nrf52840 device and the pc (while connecting via NFC) or the mobile, is configured as a half duplex or a full duplex...
Dear,
I am trying to get secure serial DFU working on our custom board, which is connected to another controller through 2x UART(P0.02, P0.03, P0.30, P0.31) without HWFC...
Hi, I am developing a central application that should get data from a single or even multiple primary services with multiple characteristics in Zephyr. I am using the central_ht...
I'm trying to build the light switch example. I have downloaded the nRF5 SDK for Mesh v4.0.0 and the nRF5 SDK v16.0.0, and place those 2 extracted folders in the same folder...
It works when I use I2C_2 to communicateon nrf9160. The register value is successfully accessed when i2C_reg_write_byte() is called.
9160dk_9160ns.overlay:
I want...
I am trying to use peripheral/spis as a reference for configuring my nRF52840 DK as a slave. The SPI clock frequency is 1 MHz. The SPI master is another micro-controller....
Hi,
I am using nrf52832 development board with sdk 17.0.2 and S132 softdevice. My requirement is to scan and advertise at the same time. I am using the ble_app_template...
hi,
I am using nrf52832 with ble multilink(nRF5_sdk_16.0.0) example. I need multiple connections with the peripheral at the same time. is it possible to connect multiple...
Hi.
I'm developing application that is needed to include UARTE Interrupt.
I can drive UART interrupt well(not UARTE), but UARTE is not working.
Here is my code...
Hi, I need to send data larger than 16 bytes on a characteristic. I see that the maximum number of bytes I can send using the indicate function is limited to 16 bytes.
...
I am working with:
NRF52840 boards
nRF Connect SDKwith Zephyr
On Ubuntu
Desired behaviour would be:
Establish connection with Codded PHY
After some time disconnect...
