I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I'm new to Nordic Semi chips (nrf52840) and need to use TWI as a master to connect to two sensors. But I'm a bit confused about the different drivers: TWI and TWIM....
Hello to all,
I have a problem related to the client side Global Attribute: I have implemented an "On / Off Switch" that presents the cluster On / Off (0x0006), client side...
Hello,
When we analyzing the traffic of our application (many thanks to the team developing the sniffer), we have several questions about sending write confirmation.
for...
We do have a product in which we program a bootloader on the target. It is remotely based on the ble_app_buttonless_dfu example. The bootloader is not actually used in the...
Hi I am building a software watchdog to monitor nrf52 peripheral states to have higher confidence for 10+ years battery lifetime. The idea is to check every few seconds if...
I am working with the S140 softdevice v6.1.0. The message sequence charts located on the Nordic infocenter are great help. Question: are they available in a printable form...
Hi,
Is there any editable software available that I can use to create a custom interface between my PC and my nrF58210 module. I have been successfully using the Nordic...
How to program flash with the output HEX file and SoftDevice file using NRF52-DK.
When programming with the output HEX file the device does not work, I need also HEX - SoftDevice...
I'm trying to set up a project with SDK 16.0.0 using FreeRTOS with the softdevice. The device will be battery powered and therefore power management capabilities are required...
Hi all,
I am trying to generally gain a better understanding of the GPIOTE module and how it can benefit myself in the project I am working on.
I am essentially attempting...
Hello
Does the nRF5280 include Schmitt-trigger inputs on the GPIO pins?
If yes, what are the voltage threasholds for the rising- / falling edges?
(Can't find anything...
Hi,
How does disconnect work in S112?
In the ble_template project, I did not find anything in DISCONNECT event.
static void ble_evt_handler(ble_evt_t const * p_ble_evt...
I have a nrf52833 pca10100 which can connect to nRF Connect Desktop to program fine. EVBW833 should have the same chip DK but it is not being recognized. Is there a way I...
Hi
On my custom board, I have an external flash connected via SPI. . The nrf runs on mfw 1.1.0.
Without activating the flash, I get an average current consumption of around...
Hello,
I am using nRF51 DK and it is programmed with s130 soft device and uart application hex file with nFGo studio.
It programmed successfully but device not showing...
