Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
When I try to copy hex files onto my board, the board un-mounts and remounts with a file called "fail.txt". The files says "OUT OF MEMORY".
I have tried hard resetting the...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Is it possible to configure the radio in such a way as to always capture the entire packet, this means everything after the preamble including the CRC? Of course this means...
I am using SDK9.0,
J-Link Lite-Cortex-M, HW: V8.00, DLL: V4.98C
But getting this error just in this project when debugging:
debug.txt
It was working with this project...
Looking at the ADC HAL, I see 8 choices for ADC input, plus a disabled case. Is it possible to choose as the input to the ADC a node that is proportional to the VCC battery...
We're building a low cost device with an nRF8001 as the only means of communication as physical access is closed after the device is built.
Is there any way to change the...
Hi Guys,
I would like to set up my nrf51822 to make a connection once a GPIO button is pressed and send some data. I've been using this sheet to try and calculate what...
Hello,
I've purchased 2xnRF905-EVBOARD
I made some test with a spectrum analyzer. The output of the module is nearly 10dBm as mentioned in the datasheet.
I connect the...
I'm using PCA10028,SDK9.0,S130.I want to set and get the ble address,but I found that couldn't get the ble address by using API sd_ble_gap_address_get,the chip will reset...
Hi, there! Does peripheral with ANCS only be connected by iOS? I ran the ANCS demo in sdk 9.0, and it works well with iOS. Once an Android phone connect to it, it was connected...
On developer site I saw "The RSSI value of the beacon measured at 1 meter distance, which can be used for estimating the distance from the beacon." I don't get it can any...
I am using HID service over GATT and have several reports defined. When I increase my report map data size by adding more reports, my map size is 280 bytes, whihc seems to...
I want to try the nRF Sniffer app but that requires that I reprogram my nRF51 dongle. I want to know that I can restore it before I do this. I can't save the current "as-shipped...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
Hi all,
I'm using two nRF51 DK to measure ADC input on peripheral side and translate it to central, based on Multilink example.
One software timer is used to perform one...
