Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
Review_4Jan.zip
Hello All,
Please review the attached revised schematic and give your valuable feedback.
Please find below queries:
In case you want to know the...
Hii everybody,
I want to do ble pairing(nrf 52832 development board) with android phone. after searching on nordic devzone how to pair device i found that pairing mechanism...
Hello all,
I have below queries on my custom board and mesh.
I have designed my custom board using nRF51824 and i am using J link debugger for programming , I can able...
Hi, I know there are already lots of threads around this but it seems none is like mine.
I'm running my toolchain on a Mac so I think I have a more challenging debug setup...
Hi,
I would like to know is there any shopping sites selling beacon modules that we can configure later based on our requirement?
I searched on few shopping sites where...
Hi,
We are developing a pretty complicated multi-threaded application on nRF52832.
Part of the requirements are storing a large amount of data over time (Megabytes)...
Hi
I am using gpio for input interrupt as below
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;
...
According to PS, external reference min. voltage is 0.83V. However, I've experimented with voltages of about 0.2V and it appears to work. Specifically, I connected a voltage...
