Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi.
I start SPI as well as I2C at the same time . then build code , the build error is occur . below is error code .
The SPI and I2C cannot be used at...
Hello,
I try to building sample code nrf_dm for nrf5340DK, but I got failed massage:
.7.0-rc2/nrf/subsys/dm/dm.c.obj -c C:/ncs/v2.7.0-rc2/nrf/subsys/dm/dm.c C:/ncs/v2...
Good Morning
Im using Zephyr, SDK2.6, toolchain 2.6. the peripheral_uart example is flashed to a 52840DK. when I connect with my phone IOS NRF_connect I get the error
...
I run the LWM2M client and send the data to the server. Nrf7002dk connects to the internet via wifi. Now I would like to update the software but I can't seem to do it. The...
Hi, I want to implement OpenThread features with another sample and I'm not sure how to go about it. Is it even a good idea to add OpenThread to another sample or is it better...
I use the serial port routine SDK17.1, nRF52833 want to burn the protocol stack, s113_nrf52_7.2.0_softdevice. But when I burn it to the chip, the address is 0x1000 and if...
Hello I have a board that I am trying to profile with the power profiler kit 2 and the readings seem very wild. I have a device that I know the base configuration with the...
I have a customized PCB with nrf52840. Pin 0.18 is used as CS pin in SPI communication.
I want to disable the nreset function and I add this CONFIG_GPIO_AS_PINRESET=n in...
I'm using the CLI interface through USB and UART, and I am wondering if there are any innate methods for checking the validity of the data being sent and received via the...
hi Nordic support team,
I cannot re-flash firmware for nrf52840 after ram off is implemented.
I recheck with other chip like nrf52833, it have the same result: \althrough...
I understand, it is possible to add variables to a section of ram, that will not be initialized (zeroed) at boot (see for example: https://github.com/nrfconnect/sdk-zephyr...
Hello,
I want to create my own board from the nrf52840. I am planning to copy the schematics given only taking into account what I need. I went through the schematics and...
Hello,
I am using the nRF51822 with SDK v9.0.0, SoftDevice S110, and the DFU bootloader v8.1.0.
For certain reasons, I want to reserve one page of the 'app data' for shared...
Hi Support Team
If a center role and a peripheral role in one nRF52840 at the same time，can the center role use code PHY and the peripheral role use 1M PHY？Many thanks.
Hi,
I need to read the data from an acceleration sensor. I tried with a custom program of mine to simulate some data, but it is delaying too much.
I tried reducing the...
