Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I have problem with send hex on flash memory in dongle. I erase fllash than plug out dongle i know that i shuldn't but raspberry sey, he can't erase falsh. Dongle has 1.8V...
Hello,
can you please advise if the GPS antenna for the dev kit nRF9160-DK would also be available separately?
Our customer received this kit with version 0.8, which does...
Since APIs have changed as new nRF5 SDKs have released from time to time, it is not clear how custom service can be implemented on BLE peripheral for nRF52840 (pca10056) S140...
Hello All
I try to port the blinki example (with softdevice s130 2.0.1) to my Hardware with the nrf51822_xxAA.
The application will run without Softdevice.
But as soon...
Stack violation: stack pointer outside stack area.
Cause: Data bus error (PC value stacked for the exception return points to the instruction that caused the fault).Bus...
Hi,
I have PCA10000 Revision 0.9.0 nRF9160 Board with external antenna (Molex 206640)
I try to make GPS work. Here is my step:
I compiled GPS under samples ..\root\ncs...
I followed the start up procedure-
All OK, but my nRF9160DK doesn't connect to the network.
Only led3 is blinking.
I think iBasis-eSIM is not enabled in my area.
I...
Hello,
I need my timer to work at 9600 bps frequency. So accordingly my frequency is 16MHz and to get 9600 Hz I calculated the prescaler to be 10.7 ~ 11. But in the timer...
I'm using nrfutil ( https://github.com/NordicSemiconductor/pc-nrfutil/releases/tag/v6.0.0a1 ) with an nRF52840 USB Dongle to update units through BLE. The device is nRF52832...
Hi,
Nordic Part Used in Design: nRF52810
SDK version used 16.0.0.
We found for nRF52810 it supports peripheral mode as well as bootloader. I didn't find any example...
Hello:
I enabled LTE and GPS in my project and I encounterd a terrible hard fault error.
The error didn't happed once I programmed my hex file.
It work fine but hard...
Hi,
Does the zephyr stack support scanning for extended advertising packets on the nRF9160?
I tried opening the lte_ble_gateway example in ncs v.1.1.0 and adding CONFIG_BT_CTLR_ADV_EXT...
Hi,
Nordic Part Used in Design: nRF52810
SDK version used 16.0.0.
We found for nRF52810 it supports peripheral mode as well as bootloader. I didn't find any example...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
sd_ble_gap_adv_set_configure() is returning error code 7 when I use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
OVERRUN error occurs when receiving UART.
I'm using EasyDMA with UART and want to increase the EasyDMA reception size. Which settings can be used to increase the reception...
