Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
Hi, I would like to interface an Alliance NAND flash to NRF5340. The flash supports SPI interface. Which set of pins will be a better choice and why ?
I am planning to use...
Hey Everyone, I am new to Nordic and zephyr. I would say I am a beginner. I am trying to setup custom drivers from ST for the lsm6dsv16x sensor. I know most of the time is...
Dear Team,
I installed segger embedded studio in my PC for working with nordic nRF52840-DK. After that I downloaded the nordic license and it was activated.Perfect. -...
If you Edit your build configuration and then add and argument using this button:
it doesn't seem to work. I've tried doing File->Save and using the Build Configuration...
As recommended by the documentation I am using the malloc/free in the common libc branch.
This code (in zephyr/lib/libc/common/source/stdlib/malloc.c) uses sys_heap_init...
I'm trying to increase the SPI speed to drive a DAC that can go up to 50 Mhz. I'm using an nRF52840 DK and SDK V17.
Even if I can set up SPIM3, there is a limit I need to...
Currently I am failing to make my two NRF24 modules communicate, to make sure the two modules weren't at a bas angle to each other to communicate I picked up and rotated my...
This is kind of just a general question out of curiosity.
Is there a functional reason to ensure that all stack sizes are powers of 2? I've seen it throughout many examples...
i am using nrf52840dk i have flashed the code for light switch lpn sample in 1 dk and 2nd dk with light sample.
i need to get help with the lpn node how it is acting as...
Hi,
I'm working on a BLE project with NCS v2.1.1 running on nRF52832. The project includes several I2C and SPI sensors. If I compile and flash the project in Windows 11...
