Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I tested the matter LOCK sample, how to disconnect the Bluetooth connection immediately after matter commissioning is completed, the log is as follows. thanks.
Hi, I am currently evaluating a Rust driver for the nrf7002-ek on a nrf5340-dk. I have been using the Zephyr nrfwifi driver for reference.
There are a large number of nrf_wifi_fmac...
When building a project using a custom board, as well as both the b0 and mcuboot bootloaders enabled, board-specific child image configuration causes the build system to ignore...
Hi All, I am looking for assistance with trying to reduce flash usage of my project. I am using NCS v2.6 with an nRF52832. Attached is my prj.conf file. The major SDK features...
Hello, I'm working on a Zigbee application using the nRF5 SDK for Thread and Zigbee v4.2.0. The app builds fine, but when running it I get the following output:
I have...
Hi All,
We are developing a heater controller using Nordic Matter Thermostat sample code. The sample code has following value.
Off
Heating set point
Cooling set...
Hi,
I use 3 devices in the Mesh application. I am looking at the Mesh:chat example. I want this,
I want to press a button on one device and light LED1 on other devices...
With nrf52840 we have different protocols to add as per application. but is it possible to include following for single application in single hex? 1) zigbee: coordinator,...
Hi
I'm testing downloading a file from AWS S3 using ncs but it's not working well. I'm getting an error called -116 Connection timed out. I also used another client to connect...
I am trying to split the external memory into littlefs storage and mcuboot secondary slot. But I'm not sure what I'm doing right
pm_static.yml
board_file.dts
Hello everyone I am using nrf5340 with sdk ncs v2.4.2, I broadcast BLE and there is a situation where it is stuck and cannot be controlled or do anything, but I can still...
I am working with an nrf9161 and I can see that the IMEI is not programmed and likely causing my connection issue. I only have the modem connected to an rtt and nrf5340 what...
Hello community,
I am developing a device that uses the NB-IoT network . I would like to know if the NB-IoT module of the nRF9160 supports SMS . If it does, will it provide...
Dear Ladies and Gentlemen,
We have recently started comparing the BM833 (and the corresponding nordic devkit nrf52840) with an other hardware (ESP32), neither uses amplified...
Hello everyone,
please take a look at my minimal reproducable example, which explains the problem and also includes some example measurements. derteufelqwe/nrf-ble-datarate...
