Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I have some issue in developing APP for devices based on NRF51822. They have been developed in 2016 with an old bootloader, when there was no use of zip pack. We usually...
My project uses nRF52832 and I'm at the point of the project where I'm trying to minimize power consumption.
To assist in this, I created a very small main() that goes through...
Dear Support,
I have tried to find the correct info to integrate the DFU functionality of the nRFConnect app on the phone into our own mobile app. We want to be able to...
Hello
I am using the NRF9160 and I can see that modem RF transmitions cause some EMI issues
I would like, for a period of few seconds each time to stop modem transmitions...
Hi, dear Nordic team,
We've already purchased a few thousands of BC805M BLE modules (nRF52805) for our upcoming mass production. During R&D, according to datasheet, we...
I need to use Delay of few Micro/ Milli / Seconds without pushing the MCU in sleep i.e. without using k_msleep() etc. Is there any library for this purpose in Zephyr ?
Hi, Hope you can help. With a nrf52840dk development kit arriving tomorrow. We tried to make a start with a nRF52840 dongle, which we eventually want to use. Connected to...
Hello,
I follow the doc to install the nrf_sniffer_for_bluetooth_le_4.1.0
- Flashing the nRF52840 dongle with nRF Connect for Desktop
Uploading image through SDFU: 97...
Hi,
I'm trying to use a nRF52840DK as a zigbee router implementing a temperature sensor. The setup is composed of
Software
Application: Home Assistant
SDK: nRF5...
Hi, I'm trying to achieve high throughput of BLE on connection between two nRF52840 DK.
I've read some articles about it, and configured both Central and Peripheral devices...
Hi,
I'm looking at the nrf5340 PS v1.2, page 75 & 76 regarding the audio clock PLL. Using the formulae given, I'm finding that the register value that yields the closest...
Very much a beginner at this so if this is inappropriate for this forum do not hesitate to let me know.
Starting out trying to develop a BT Mesh system. I purchased a nrf53...
Hallo Dears,
I would like to develop a ble-peripheral role device with a humidity sensor service. I found the development kits from the nRF5x family such nRF51, nRF52...
Hi,
I'm trying to take advantage of nRF52840 as Zigbee NCP in communicate with a host microcontroller via UART. My problem is I don't know what I have to send and what will...
Hi,
In your LE audio presentation from CES that you had a demonstration of a low latency setup with LE audio. We are more curious about the setup you demonstrated so we...
