I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
I am evaluating the output power of a testboard that uses the nRF52840-QFAA.
The matching network closely resembles the recommended network in the datasheet (shown in figure...
Hi!
I am using MCUBoot and the DFU library to perform a custom firmware update (which is working as expected).
I have a question about the "swap_type" value, which is...
Hi Nordic team,
I’m seeing a repeatable configure hang with NCS v3.3.0 sysbuild on macOS. The visible build output stops after:
After inspecting the process tree, CMake...
Hi Team,
I need to use this external clock for my deep sleep use case so let me know the step forward for the same.
I am using custom board with nRF54L15 and also LXFO...
HI all,
The main program suddenly encountered assert （nrfx_grtc.c line 278）while running, which happened by chance. The following are the relevant logs
note:nrf54l15...
Hi, all!
I'm currently facing an issue with upgrading the nRF52840 firmware on a Thingy91 and would greatly appreciate your guidance. I'm following the official instructions...
Hi everyone, I recently encountered an issue while developing with the nRF54LM20A. When acting as a USB High-Speed (HS) HID mouse device, Endpoint 0 fails to respond with...
Hi,
I started from your
Bluetooth Mesh NLC: Lightness Controller/Energy Monitor sample
and I tried to insert a Light CTL Server model in the project.
After a lot of...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi,
I am using the Nordic UART Service (NUS) on an nRF52840 with NCS. Without pairing enabled, NUS works perfectly with the nRF Toolbox UART service — both sending and receiving...
In the nRF Connect SDK v3.3.0 release notes, I noticed that the QoS Channel Survey feature has transitioned from experimental to supported (i.e., production-ready).
From...
Hello Team,
I am working with Thingy91x and I was checking whether is pwm led or pwm gpio can be configured for nRF5340 of Thingy 91x. If possible will you please let me...
