Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Recently I develop products on nRF5340, I plan to make the full BLE stack run in the net-core, and app-core only runs application. It involves data exchenge between net-core...
Hello,
We have a application with soft device on nrf52832 with SDK 15.3 with 60 uA power consumption. It works as it seems for now.
We wanted to add DFU buttonless feature...
Hi,
We were using Nordic HAL for FEM modules to drive our PA/LNA using nRF52840 on zephyr (no NCS). It was only a basic configuration, where the PA and LNA pins were selected...
Hi.
I have a quick question regarding the RSSI Value of Messages sent in a Bluetoth Mesh Network.
So my question is: How exactly is the RSSI Value defined and how does...
I have a few questions about the DFU:
Is it necessary to flash everything together (Bootloader, DFU, APP) for the initial programming when testing buttonless secure DFU...
If you remove power from the beacon right around the time when the LED is going to start flashing to indicate power on, and do that a number of times you will see it will...
I successfully ran the asset tracker with the 9160DK and am able to receive all data correctly, certificates seem to be working, and everything works as mentioned in the asset...
Hello,
We have a large application using ESB to communicate between many nRF52840 devices. All devices are using firmware with SDK 17.0.2. These devices often switch from...
Hi,
I am using nrf52832 DK.
SDK 17.0.2 softdevice S132.
I am using freertos and running nrf52832 as a peripheral.
I want to put nrf52832 in sleep mode.
I am new...
Hello,
I am migrating code from nrf5_SDK_17.0.2 to nrf connect sdk v1.6.1. The board i am using is nrf52dk(nrf52832) connected with adafruit LSM6DSO.
Everything works...
Hi,
How can a specific folder structure can be realized in an SDK project.?
We want to create some folders and follow folder structure in nCS example and develop our...
Hi,
I am currently working on buttonless DFU for my application and I encountered a problem when I generated the .zip file.
In this line
--sd-req, in this case...
I wanted to send 'zdo mgmt_lqi 0x0000' through the serial port to get the 16-bit short address of the ZigBee terminal device, but I found that I did not return the value for...
Hi,
We are planning a product with BLE mesh capability using nRF52840 and a few sensors. The system power is from 2 AA batteries. We have 2 configurations in terms of power...
