Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I was merging the files of peripheral hr in ble mesh chat project
how to add new .a project in nrf connect sdk using segger embedded studio and also how to include...
Have a catch-22 here.
Here is my code:
When I call nrf_sdh_enable_request() it returns the error '0x08 which is SoftDevice already enabled according to the documentation...
Hi everyone,
I use to use the nrf52840 dev. board with the SDK16 examples. Now I am facing a problem with all the BLE peripheral examples
1. When I build and run in release...
Hi there,
for a customer of mine I have to programm a Arduino 33 BLE but not using Arduino IDE but use the Nordic SDK.
As it is a normal nRF52840 (inside an Nina-B306...
I am currently working on a project in which I will need to increment the pwm up to full cycle in 'x' number of steps and then be able to step down 'y' number of steps when...
I'm using app_scheduler to pass UART events in the "main thread". I'm storing multiple data types in a struct (arrays, integers) and I've set the max event size to the size...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
Hello,
I am preparing to develop a design using the nRF52840 and would like any guidance or consideration for an LDO usage. I have found some previous mention regarding...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
