Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello All,
There are several issues where I can see RTT viewer is not working along with nrfjprog tool etc....
I am also facing similar issue where RTT viewer(version...
Hi,
While I can find many discussions about how to set the MAC address using the soft device API with previous SDK's, I cant find a way to change the MAC address of the...
New nRF52-DK PCA10040 2.1.0 2021.24
The out-of-the box "Get Started" procedure where I move my iphone near the antenna did not work (did not pop up any web page). NFC was...
Hi,
I'm leveraging the ble_app_cli example program for my project. The primary reason for this is that I need BLE and I need to be able store and retrieve log data which...
I'm downloading a firmware image from AWS via cell onto the nRF9160. I want to perform a serial DFU over UART. The DFU target is the nRF52840. Are there any existing samples...
Hello DevZone,
I want to send a simple AT-Command like: AT\r\n from the ESP32 to the Fanstel BC805M (nRF52805M) breakout board.
Problem : The Esp32 does not get a...
When handling a `BLE_GATTS_EVT_WRITE` from a queued write, the write event has the characteristic handle set to zero. How can I identify what characteristic is being written...
Hey there!
I'm new in the development with the nrf9160dk. And I wanted to connect the Murata SCL3300 digital inclinometer to the development kit via the SPI lines. However...
It's been a while since this Java developer really understood EE concepts.
Could someone jog my skills and explain to me roughly what the different pin rive modes are,...
Hi,
I need to send custom messages to models on my devices and I need to use a vendor model like I've seen other people on this forum use. But when I load the nRF Mesh...
Hello,
We are interfaced the nrf52811 with LSM6DSO32 through i2c and LSM6DSO32 is connected to Auxiliary(Temperature MAX30208) sensor through mode 2 connection. here I am...
I am trying to learn to use the nrfx API to control the nrf5340.
My installation is the NCS 1.6.0 with SES on OSX
It seems like nrfx most of the API devices are supported...
I'm trying to find a battery for my application and I need to know the max (peak) current draw for the nRF9160. On page 63 of the user guide, the max is 435mA with the specs...
