Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
A project I am working is proposed to have an nrf 5340 connected via UART to Yocto (Thud). Am looking for suggestions on an embedded client that will work with v3.0.0 of the...
We are using this custom baord to check the I2C addresses where the I2C BQ_SCL (P1.00) and BQ_SDA (P1.01) connects to various peripherals. However we are unable to get the...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hi,
I am trying to install nRFconnect SDK and VS Code Windows 10 by following NORDIC Dev Academy lessons.
Encountering following errors while building the following example...
in C:\ncs\v3.0.2\nrf\subsys\bluetooth\services\nus.c
The property of BT_UUID_NUS_TX only declares notify, but the permission declares read. After the nRF Connect app is...
Hello. I'm using the nRF52832DK in a test fixture application.
I need the embedded system to know when either:
- a PC has connected and disconnected to the main USB...
Hi everyone ! I am having trouble trying to flash a custom firmware to a nrf52840 board connected to another custom board using P19 debug out I am flashing the code directly...
Segger j-link target device list doesn't have nrf9151_xxAA
This means I have to manually select nrf9151_xxCA every time as a work around.
Is there any way it can be a...
Hi, I'm working on an application that transmits data via USB CDC/ACM class. I'm trying to improve the robustness of the application, and I realised that if the USB cable...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
We built our own hardware using the nRF54L15. It connects fine with the Android BLE Debug Assistant and has a 30% chance of connecting successfully with a Windows computer...
Hi,
I’m using the Power Profiler Kit 2 to measure current consumption on an embedded device, and I typically transfer the data to a PC via the Power Profiler Kit software...
Hello!
I'm hoping to use the nRF52820 (QFN package) powered by a USB connection (not with external battery).
I'm referring to Figure 153 of the datasheet, which shows...
