Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
My provisioner is a light switch client on a dev kit NRF52832.
Now I want to define it as a proxy node as well but I suspect that my Android App cannot send one generic...
Sorry I'm looking in the AoA.
I See that in zephyr main line there are 2 samples :direction_finding_xonnectionless_rx direction_finding_xonnectionless_ tx..
Hawe I to...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
Hi good evening,
i am working on a project that requires ble transmission between 2NRF52dks and one of them is connected to a PC and apart from receiving data from another...
Hi Devzone,
I have 2 question about Thingy 91:
1) When I come to area that don't support NBIoT or LTE-M, Does the Thingy 91 connect to cloud (nrf cloud, mqtt broker,....
We have developed an Android application for a customer (Ibiza) which makes use of nRF's Android-BLE-Library ( https://github.com/NordicSemiconductor/Android-BLE-Library ...
I defined a timer and start the timer when application open gps, it can prevent the timeout of star search failure; When the gps search star successful, I will turn off the...
Hi,
Now I using the nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 to develop the zigbee function on nRF52840,
I am using the light control Example,
it provide two examples to...
Hello,
I'd like to know how to interface with the SDK libraries(as a "beginner") and ask how do you approach such a thing and learn how to use it? let's take for example...
Hello,
I have an xon / xoff flow control implementation with nRF52833 DK.
The setup is the nRF52833 DK is connected to the computer through USB cable.
A python script...
So far, since UART has been working well, now, we are switching from UART to RTT to remove UART port connection from our PCB design.
However, the output to RTT is working...
