Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi, I am using nrf5832 sdk 14.2 where I am trying to scan the data and advertise same data with some modifications. I have used Central and Peripheral example ble_app_hrs_rscs_relay...
Hello,
I am trying to compile the samples from SDK_for_mesh_v4.2.0 but i have problem with my environment set-up. I am following closely the documentation but I think something...
Hi everyone,
We have three ADC channels, two of them are implemented as a simple ADC without oversampling, the third one uses oversampling. Because one of them use oversampling...
Hi, I have started development on nrf52840DK . 1-I have installed nrf Connect SDK v1.3.0.
2- I have also installed Segger Embedded Studio Nordic Edition. and selected nrf...
Hello, Please help i m trying to share memory between Network and App Cores in a nrf5340
How To do?
at page 21 Figure 2 Memory Map
it seems that FLASH address 0x0000...
Dear Sir.
Some problem with the PWM .
Pwm output on pin 12 is connected to a buzzer.
When pwm_pin_set_usec(pwm_dev,PWM_IO, 260, 130,0) is set through the pwm_init...
I'm trying to achieve half-duplex UART communication between two nRF52840-DK:s (master/slave) using no external circuitry. I was looking at the thread https://devzone.nordicsemi...
Hello
I am using SDK16, and using BLE sample project (central app_ble_blinky)
when I am taking sample project without BLE , I am able to add UART secure bootloader...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi,
We are developing the BLE product based based on the nrf52840 Chipset and we are facing below problem while testing in the field.
During our development we have come...
Hi,
Based on other discussions of encryption etc , I created a function to encrypt all the data, so that whenever I call the function It encrypts.
But I am not able...
Hello,
I’m struggling with a problem and need your help. I have an application where a nrf52840 communicates with another nrf52840 over BLE using nus and some services....
I am about to follow the steps here https://wiki.segger.com/Open_Flashloader to be able to program an external flash. However if there is an easier method I would prefer to...
Hello, i would know about the IDE avaiable to develop codes for SoC Nordic nRF52840 and where i can find/download it
Moreover, where can i see examples code about BLE Client...
Hi
I'm working with FreeRTOS with Tickless (RTC) and I was wondering what one should do in order to avoid the FreeRTOS Idle Task to be waken up every time an Interrupt Service...
