I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi!
I am planning to move sample code of uart.because I port the function of uart to spi sample code.
now i take the SDK14.0.0 and uart sample(examples/peripheral/uart...
Hi, I can make a DFU over BLE with nRF connect 2.5.0 Bluetooth Low Energy, all is OK. I use my nRF52840-Dongle PCA10059 (Serial port: COM19 | USB: Nordic Semiconductor nRF52...
Hello,
I'm using SPI 3 to communicate with a NAND memory. I'm able to go up to 8MHz but not more than that. Do I need to set an array list or use the spi manager.
Is there...
Hi Nordic Support, community,
Recently I started working with the nRF52 dongle, after flashing a hex file via nRFConnect/Programmer applic (version 2.5.running on Windows...
Can anyone tell me where the board / device choices in Eclipse come from, as shown in the screen shot below? I have none.
I copied my Eclipse installation from a working...
Hi all I've already setup my Eclipse environment as described in Development with GCC and Eclipse . Now I want to use the SPI libraries for my example. But I got the first...
Hi
The compiling of standard TWI sensor example is giving me an error with SES.
Please find attached a snapshot of the issue.
Need your help ASAP. Thanks
Ch...
My pcb is nrf52832 based, with SPI interfacing ICM20649 sensor.
- Nordic SDK 11.0
- Softdevice 2.0
I am able to flash example code of SPI based ble_peripheral and mpu...
Hello,
I am using an app_timer on my nRF52840 (SDK 15, Softdevice 140) to keep track of the time on my device. After a specific event, I would like to be able to clear the...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
I have been successfully using nRF Connect v2.5.0 on Windows with a PCA10056 v0.9.2 to communicate with our target device, a nRF52840 using S140 v6.0.0, nRF5 SDK 15.0.0. We...
I have four button and one external interrupt from GSensor on my demo board, and I use GPIOTE_CONFIG_IN_SENSE_TOG for button and GPIOTE_CONFIG_IN_SENSE_LOTOH for GSensor interrupt...
Hi, I am wondering what cost-effective JTAG debuggers you can use with the nRF52832 hardware using the 10-pin standard debugging header. For example, has anyone used the Segger...
Hi All,
I am using the nRF51822 board and have it connected to a micro SD card shield using SPI.
I have not changed anything in the example file with the exception of...
I have a question.
Two slaves connect one Master.
At that time, Can another Master automatically connect the two slaves ?
I know softdevice110_v7 has connection state and...
