Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
This is not a support request.
I just want to share some code that others might find useful. If I post it here then they might find it.
The current RADIO_TEST example...
Hi,
I'm trying to use RTC to generate interrupts at every second. The rtc event handler is below:
In the RTC examples, nrfx_rtc_counter_clear is used to reset the RTC...
We are using the nRF5340 with the nRF7002 Wi-Fi module on our custom board. Our application periodically sends data to a server. During continuous testing, we encountered...
nRF Connect SDK with VSCode has suddenly stopped working.
Problems
When I try to create a new application by copying a sample, it says "no samples available".
When...
I created an application that stress-tests wifi scanning and neighbouring cell scanning, on nrf9151 with wifi extension board. Wifi network scanning and neighbouring cell...
I am using peipheral lbs sample and modifying it for my project use. By default it doesnot has pm_static.yml where addresses could have been defined. Once i build the modified...
Hi everybody,
I have problem with my nrf9151-DK. If I switch my kit do AT-Command mode (I use Serial Terminal of Nordic, v 1.4.3), I am not able to switch my kit to PPP...
I'm porting some code from nRF52832/nRF52840 to nRF54L15 using the MPSL timeslot API. The old code uses MPSL version v2.5.1, the new v2.9.0.
The firmware opens a session...
I am evaluating Bluetooth Periodic Advertising with Responses (PAwR) using a NRF52840 Development Board. I am very satisfied with the development environment and the nRF Connect...
Hi
I want to check the nRF54L15 ADC Rsource value
As below pic., P1.07/AIN3 input voltage will be 0.6V (1.8V divider by R429 & R428)
So the Rsource value will be R429...
Hi,
I am trying to build an app for nRF5340 and I am getting the above error. When I look into my 'C:\Projects\nrf\nrf5340_coap\build\zephyr\include\generated\devicetree_generated...
