Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I have a simple project running on a custom board with a nrf54L10 processor. The board has a couple of LEDs to blink and advertises on BLE. With v4.3.0, the LED blinks for...
nRF54L10 + NCS 3.02
A simple question: So I found CONFIG_MCUMGR_TRANSPORT_BT_DYNAMIC_SVC_REGISTRATION=y which lets me enable/disable the SMP service. Is there another config...
I am using nRF5415-DK and SDK v3.2.2
I want to generate a sine wave using PWM and TIMER. The PWM repeat duty cycle method has limitations, so I am using a timer to trigger...
Hi, for one of our products we are evaluating an option of porting the application from nRF5 SDK (nRF52) to nRF Connect SDK (nRF54). Seeing the similarity between the nRF...
Hello DevZone,
I am currently trying to fix an issue I have on deployed devices, using nRF9160 with nRFCloud. Code is based on SDK 2.8.0.
In most cases, my code works...
I am attempting to use the nRF52840 QSPI periphery to communicate with an SRAM chip. The chip is IS66WVS8M8FBLL-104NLI. I am unable to communicate with it using QSPI. I am...
Hi everyone,
For mthe prject I'm working I must use the LPCOMP module to detect a cross. but anytime a init the LPCOMP module my code seems to freeze and nothing else...
Hi,
I have developed a Matter-over-Thread light bulb using the Silicon Labs EFR32MG24 platform, with CHIP_CONFIG_SECURITY_TEST_MODE = 1 enabled. In parallel, I have set...
I am currently porting an internal application to the nRF54LM20 and am attempting to manually trigger a GPIOTE30 interrupt via software.
Observed Behavior:
Hardware...
Hi,
I am working on a custom board which is NRF54L05 connected to NRF54l15 DK via P19
NRF54l15 DK version: PCA10156 0.9.3
Serial wire debug cable length: 15cms
Breakout...
I'm kind of stuck here. I was using SES v3.52 on Mac OS Sequoia and everything worked fine. I upgraded my MacBook to Tahoe and all of the fonts were messed up making it un...
Hi.
Using Thread Topology Monitor and NRF52840-DONGLE I'm able to connect to the device and getting the UDB device to be a Thread Leader.
But how can I join an existing...
I am using the command AT+CRSM=176,28539,0,0,12 to attempt to read the FPLMN on the my nRF9160 DK. The modem firmware version is 1.3.5. See attached logs:
(14:11:15.629...
I have built the Matter temperature sensor sample for the nRF5340 running on an nRF7002DK (no WiFi enabled). The power consumption measured with a PPK2 is coming in higher...
Hello,
I am developing Channel Sounding Test Mode functionality using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
