Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I'm currently testing LPCOMP with one of our nRF5340DK boards.
The power consumption of the LPCOMP seems way too big (around 140µA) once enabled with this conf...
Dear Nordic Engineer
Our customer uses NRF52832 to develop a computer remote control pen. They are based on the keyboard example in the 15.3.0 SDK. Now they encounter some...
I have a working (hand-wired) prototype that connects to the internet without any problem.
Now I have made a PCB to replicate the same thing and loaded the same software...
Hi, I do have a PCA10040 board, I'm using the examples from Nordic. On the DFU example for SDK 12 I have pressed button 4 and RESET the board to active BOOT . I’m testing...
Hi,
S112/S113 is currently the only supported SoftDevice on nRF52805 and doesn't support Central (Only Peripheral). Is there a plan to enable S132, SoftDevice Central are...
Hi,
I have nRF52840 DK boards.
This is rather an informational question for my benefits.
In post: https://devzone.nordicsemi.com/f/nordic-q-a/9315/nrf52-802-15-4
...
Hi,
I’m developing a BLE joystick with nrf52832 with a PCA10040 board
To make the development simple I’m using 16 input Buttons and 2 analog inputs with 8 bits each. ...
Hi,
We have a product that is based on 2 SDKs : SDK 14 and SDK 15. SDK 15 covers nrf52840 builds and SDK 14 covers nrf52832 builds. I know this is not perfect setup but...
Hi,
We are using SDK13 and nrf52832.
I will use BLE security mode 1 level 4.
It is in progress referring to "ble_app_multirole_lesc".
How do you check "App completes...
Hi,
I have VSCode and Segger Ozone installed along with the nRF Connect SDK (v1.7) and the nRF Connect Extension for VSCode. I can successfully build example projects and...
Hi,
I am new and just starting out. I am using a nRF51822. I downloaded SEGGER and the nRF sdk (nRF5_SDK_17.1.0_ddde560), but I can not find nRF51822 in the config folder...
Hi,
We have made a custom board based on BMD340 for a vital signs monitor. The board will be attached onto various parts of human body. The body shadowing effect plays an...
Hello，I am developing a stethoscope project with nrf52832 platform. Now I encounter a problem: when Xiaomi m2004j19c mobile phone connects to nrf52832 platform device 1, and...
I'm designing around part 1490-1071-2-ND (nRF52840-QIAA)
Your ref designs show DEC5 decoupled with C9, 820pfF and states "not required for Fxx & later"
Do I need to place...
We are starting a new Nordic-based project and are looking through the nRF Connect SDK 1.7.99 documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
