Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello All,
I have a specific requirement to run 2 different functionalities from the same HEX file. Can someone suggest is there any means of special logic in the nRF52...
I have successfully ported the fatfs file system to my application code, but copying the files is very slow. I'm trying to modify the mass_storage.c file,follwing is my code...
I have two nRF52832 feather boards. Trying to set a simple connection between them so that board 1 sends beacons and board 2 receive them. Every few minutes, board 1 pair...
Greetings,
I am trying to run the scan_adv example from the samples. I am using the nRF52832 kit and SEGGER for running this sample. However, I face the error mentioned...
Hi everyone,
I am following this video step by step to create my custom board configuration https://www.youtube.com/watch?v=KSivO9Cf1TE&t=474s .
I follow every steps but...
Hi all,
My project can be built and run correctly on NRF SDK 1.5.0,
after updated to SDK 1.6.1 and rebuild, it failed and messages below:
Is there any idea for this...
After installing nrfConnect SDK v1.6.1 on MacOS ( Big Sur 11.5.1 ) using Toolchain Manager, I can't find nrfjprog.
When I try and run nfrjprog in Terminal, I get: "zsh:...
Because some IOS devices support up to 185 Bytes MTU, Android phones 247.. is there
any possiblitly wow the Application Core NRF53 can retrieve the current MTU Size from...
Hi
I am working on a nRF52840 using Zephyr as OS.
I have setup some control GPIO pins in the device tree (se below). This works fine from the application. I can access...
When I enter 100 as the size for the ATT MTU all works perfect, but when I choose a larger number like 250 as ATT MTU, sd_ble_enable() does not return an error and I can debug...
I will be using an NRF5340-DK for starters. I have a Linux SBC that will be running blueZ. I can use USB, UART, or SPI to connect the NRF5340-DK to the Linux SBC. I am assuming...
Hi Dev Team,
I had installed the newest NCS version NCS v1.6.1 and was importing my application from 1.5.1 to 1.6.1.
However, I noticed a lot of changes with respect to...
Hi,
I have a question ,According to the official tutorial，I succeeded BLE OTA DFU in windows system by nrfutil ,however, when I use the nrutil tool to update the firmware...
I have tried to use I2C but it does't work out. nRF9160 doesn't start booting after executing "build and run" and pushing the reset button.
I open secure_boot project...
