Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
Good evening. We're running into an issue with using all 4 peripherals on the nRF9151. At the moment we are using the 9151DK.
The issue arises as soon as we enable spi1...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
When I use DTM mode and config nRF54L15 to 8dBm, I only see 5.3dBm. And I tried 3 boards, they are the same. Is that normal or not
The whole cable loss is lower than 1dB...
I just received a Thingy 91X, and am having problems out-of-the-box. I used the "Quick Start" module of the SDK. I selected the option that programs the hello.nrf.cloud connectivity...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I have been using visual studio code on mac for development, and it started showing error code 63 when I try to start debugging on the 9160 based hardware. It used to work...
Hello,
I am studying the materials in Bluetooth Low Energy Fundamentals.
I cloned the codes from GitHub https://github.com/NordicDeveloperAcademy/bt-fund
I tried to...
Hi,
If you use the following settings, an error will occur during commissioning.
Board: Custom board
SDK:ncsv2.9.2 OS: Windows10 Sample code:Matter Lock bord target...
Hi,
I’m new to working with nRF MCU and I’ve just purchased an nRF52840. I want to use it with my own custom board, but I’m not sure where to start. I would like to use...
We're running SDK v2.6.0 on a nrf5340 processor and initiating a connection to a specific heartrate monitor using the bt_conn_le_create() function. What function do we call...
Hi, DEVZONE,
Can you suggest a proper samples and tell me what are must-have configurations ?
nRF (zephyr) SDK v3.0.1 or v3.1-rc1 versions are preferred.
Also, can...
I'm looking at the example esb_ptx and esb_prx from SDK v3.0.2 running on an NRF5340 and NRF52840 respectively.
This function in esb.c
sets packet_config.flen based...
Hello Nordic Team,
I am writing on behalf of my company, where we are developing a cross-platform application using .NET MAUI . As part of our application, we need to implement...
